DPCAV
ELOGGER BATTERY BACKUP HARNESS
| Instruction manual | Click Me! |
This 3-inch long harness cable allows you to power the eLogger from a separate 4.8V to 6.5V battery. There are three common situations where this cable is required:, (1) In installations where the primary battery or BEC frequently dips below approximately 4.5V, which causes a “reboot” of the eLogger system.,
(2) When using the GPS Expander on your eLogger with ...DPCAV
RSSI BUFFER FOR OSD PRO
| Operating Voltage | 5VDC (powered by EagleTree eLogger). |
| Current Draw | 2 milliamps. |
| RSSI Voltage Range | 0 - 4.0 VDC. |
| RSSI Input ohms | > 1 megohms (DC). |
| Input Impedance | 330K ohms (AC). |
| Size/Weight | 0.45 x 0.73 inches (11 x 19 mm), 2 grams. |
| (note | video is courtesy of R. Bill, a very satisfied user.) |
Specifications / Features:, Installation Instructions:, Click Me!, Cable Pin-Out Information:, Click Me!, Installation Video:, Click Me!,
The RSSI Buffer is a tiny-sized accessory that is used ...DPCAV
GFORCE SENSOR, LOW G
| Resolution | approx. 0.05 G in each axis |
| Maximum | ±7 G in each axis |
| Power input (Standalone Mode) | 4V to 16V |
| Weight | approximately 4 grams (0.15 oz) |
| Dimensions | approximately 28x16x10 mm (1.1x0.62x0.4 Inch) |
| GFORCE-LOW Instruction Manual | Click Me! |
Specifications and Features:, ,
This tiny G-Force sensor is factory calibrated to measure up ...DPCAV
ELOGGER VIDEO OSD-PRO EXPANDER MODULE
| Video Compatibility | NTSC / PAL. |
| Power | Provided by eLogger V3 (sold separately). |
| Video I/O | Two 3-Pin headers. |
| Audio I/O | Two 3-Pin headers. |
| Size | 2.4 x 1.0 inches (61 x 25 mm). |
| Weight | 0.5 ounces (13.5 grams). |
| Instruction Manual | Click Me! |
| Eagle Tree Web Site | Click Me! |
The OSD Pro is a powerful, modular, and fully configurable video/audio On-Screen Display (OSD) device. It provides graphics and voice announcements that report a variety of alarms and data, including: acoustic variometer, electrical performance, Home Arrow, Return to Home, Failsafe, “RADAR”, waypoints, and many other features., how YOU configure the display. Here's a screen shot that shows some of the information that can be shown:, , All the data parameters that are supported by the eLogger can be displayed on the video display. Here are some examples:, , Specification Summary:, IMPORTANT NOTE: The OSD-Pro requires the EagleTree eLogger V3 or V4 module. To display navigation related data the GPS expander module is needed. These items are available separately (please see the related items links shown near the bottom of the page).,
The Eagle Tree Video OSD Pro Expander module adds graphical ...DPCAV
ELOGGER POWERPANEL LCD DISPLAY EXPANDER
New Feature:, The PowerPanel LCD is normally connected to the eLogger module. But when one is connected to the “Exp” port of the, Features (eLogger Installations):, • Ultra-thin LCD display., Features (EagleEyes Installations):, • Easily mounted on the EagleEyes plastic case., Instructions, eLogger & Power Panel:, Click Me!, Instructions, Power Panel only:, Click Me!,
The eLogger PowerPanel LCD Display Expander provides real-time data in ...DPCAV
RSSI METER KIT (ASSEMBLED)
| Supply Voltage | 7 - 14VDC / 10mA |
| Min RSSI Voltage | 0.0VDC |
| Max RSSI Voltage | +5.0VDC |
| RSSI Scaling | User configurable |
| RSSI Impedance | ~57K ohms |
| Character Height | Large 0.5-inch (12.7 mm) |
| Display Type | LCD (daylight visible / high contrast) |
| Dimensions | 1.8 x 1.4 x 0.25 inches (45 x 35 x 6 mm) |
| Weight | 6 grams |
| Instruction Manual | Click Me! |
Connection to your receiver requires three wires: Power, Ground, and RSSI signal. A simple push-button interface allows fast and easy signal strength calibration., Specifications/Features:, ,
The RSSI (relative signal strength indication) Meter displays a video ...DPCAV
ADJUSTABLE VOLTAGE REGULATOR, 1-35V STEP DOWN
| IN+ | Battery/Power In + |
| IN- | Battery Ground |
| OUT+ | Regulated Voltage |
| OUT- | Common Ground |
| Input Voltage | 7-35VDC |
| Output Voltage | 1.2VDC-30VDC |
| Output Current | 2A / 10W maximum |
| Switching Frequency | 150KHz nominal |
| Power Efficiency | 83% typical |
| Output Ripple | 60mV at 10W loads typical |
| Technology | Switch-Mode Buck Regulator |
| Voltage Adjust | Screwdriver Access |
| Size | 1.95 x 0.9 x 0.5 inch (50x22x12mm) |
| Weight | 11 grams |
The circuit board has four pads (soldering required) that are labeled as follows:, , Specifications:,
This Voltage Regulator has an adjustable 1.2VDC to 30VDC output. ...DPCAV
ADJUSTABLE VOLTAGE REGULATOR, 1-35V SEPIC TYPE
| IN+ | Battery/Power In + |
| IN- | Battery Ground |
| OUT+ | Regulated Voltage |
| OUT- | Common Ground |
| Specifications | Input |
| Output | 1.2VDC-30VDC 2A / 10W maximum |
| Switching Frequency | 60KHz typical |
| Output Ripple | 150mV at 10W loads typical |
| Technology | Switch-Mode SEPIC Regulator |
| Voltage Adjust | Screwdriver Access |
| Size | 1.9 x 0.9 x 0.5 inch (49x22x12mm) |
| Weight | 15 grams |
The circuit board has four pads (soldering required) that are labeled as follows:, ,
This Voltage Regulator has an adjustable 1.2VDC to 30VDC output. ...DPCAV
R/C CONTROLLED DUAL VIDEO SWITCH (2-WAY)
| Video Switch | Solid State SPDT Relay |
| Video Bandwidth | 10MHz |
| Video Insertion loss | 0.1dB typical |
| R/C Pulse Range | Industry standard 1.0mS / 2.0mS |
| Status Indication | Red / Yellow LED |
| Power | 4.5 - 13V / 20mA (provided by R/C receiver) |
| Size | 1.3 x 0.9 x 0.20 inches (33 x 23 x 5 mm) |
| Weight | 5 grams |
| Installation Instructions | Click Me! |
Features / Specifications:, ,
This R/C system activated video switch allows you to remotely ...DPCAV
900MHZ HIGH GAIN YAGI ANTENNA, +9DBI
| Frequency | 890 to 960 |
| Gain | +9dBi |
| Polarization | linear |
| Connector | Includes SMA plug and |
| Coax Cable | 18-inches, low |
| Antenna length | 20 inches |
| Weight | 1.5 lbs (0.7 |
| Data Sheet | Click Me! |
| Instruction Manual | Click Me! |
| Mechanical Drawing | Click Me! |
Specifications / Features:, , Horizontal beam width:, 54, Vertical beam width:, 48, Impedance: 50, Maximum power:, 100W, Mast U-bolt diameter: 2,
The HG909Y high-performance Yagi antenna provides +9dBi of gain. Can ...DPCAV
900MHZ ANTENNA, V-DIPOLE
| Frequency Range | 880-980MHz |
| Gain | ~2dBi typical |
| Impedance | ~50 ohms |
| Polarization | Linear |
| RF Power | 10 watts maximum |
| Connector | SMA Plug (male) |
| Size | 4.6 inches (115mm) tip-tip length |
| Weight | 13 grams |
| Color | Green |
| Instructions | Click Me! |
Cable Length:, 10 inches (250mm) long,
This lightweight V-Dipole style antenna is designed specifically for 900MHz ...DPCAV
1.28GHZ ANTENNA, "BIG STICK" +7DBI (1258/1280MHZ)
| Frequency | 1240-1320 MHz (1.2GHz-1.3GHz / 23cm ham band) |
| RF Gain | +7dBi |
| Type | Omni-directional coaxial sleeve dipole |
| Polarization | Linear |
| Horizontal beam width | 360° |
| Vertical beam width | 26° |
| Input Power | 20 watts max. |
| Length | 15.4 inches (390mm) |
| Weight | 46 grams |
| Data Sheet | Not Available. |
DPCAV
1.2GHZ - 1.3GHZ ANTENNA, V-DIPOLE
| Frequency Range | 1240-1320 MHz |
| Gain | ~2dBi typical |
| Impedance | ~50 ohms |
| Polarization | Linear |
| RF Power | 10 watts maximum |
| Connector | SMA Plug (male) |
| Size | 3.4 inches (87mm) tip-tip length |
| Weight | 13 grams |
| Color | Green |
| Instructions | Click Me! |
Cable Length:, 10 inches (250mm) long,
This lightweight V-Dipole style antenna is designed specifically for 1.2GHz ...DPCAV
CUSTOMIZED CABLE FOR LAWMATE A/V TRANSMITTER
| Red | +12VDC, to battery |
| Black | Common Ground, to battery |
| White | Audio input, connects to microphone or OSD |
| Red | +12VDC (from DC-IN) to power 12V microphone |
| Black | Common Ground |
| Orange | Video from camera or OSD |
| Red | +12VDC (from DC-IN) to power 12V camera |
| Brown | Common Ground |
Referring to the photo below, a summary of each connector is as follows:, , Battery:, JST (BEC) style female cable. Goes to the 12VDC battery that powers the video transmitter and camera., Audio:, Futaba male style servo cable, goes to optional microphone or OSD Audio-out port., Video:, JR/Hitec male style servo cable, goes to video camera or OSD Video-Out port., TX:, The TM-121800 video transmitter's cable plugs into this 4-pin connector.,
Upgrade your transmitter's bulky RCA cables with this custom wire ...DPCAV
CUSTOMIZED A/V CABLE FOR SKYRF / BOSCAM / FOXTECH TRANSMITTERS
| IMPORTANT | This cable is NOT compatible with Immersion-RC or Fat-Shark transmitters. |
| Orange | Audio input, connects to microphone or OSD |
| Red | +12VDC (from TX) to power 12V microphone |
| Brown | Common Ground |
| White | Video from camera or OSD |
| Red | +12VDC (from TX) to power 12V camera |
| Black | Common Ground |
| Note | The |
Referring to the photo below, a summary of each connector is as follows:, , Audio-In:, JR/Hitec male style servo cable, goes to optional microphone or OSD Audio-out port., Video-In:, Futaba male style servo cable, goes to video camera or OSD Video-Out port., TX:, This 5-pin connector plugs directly into the TX5.8-200 video transmitter.,
Upgrade your SkyRF / Boscam / Foxtech type 2.4Ghz or ...